Feed Extruder Machine

Puffing machine operation and use of technology and precautions
1, choose no impurities and hard materials (such as the purchase of small puffer, the material to be processed need to be crushed to the size of rice grains in the processing.)
2, before starting the machine, tighten the head nut and gear nut, the rear nut of the belt disk, the belt should be pulled tight.
3, start idling normal, can be a small amount of slowly add materials, to be puffed out of normal, immediately add a small amount of continuous materials, to be puffed out of the molding, and gradually increase the amount of feed, the amount of feed to the principle of the power to drag.
4, such as found at the mouth of the feed material up to turn back, because at the beginning of the machine has not yet risen to the normal temperature, put too much material, the material can not come out in the material to turn back. At this time should stop discharging, to be put again after the material turned down, must be continuous operation processing, 5 minutes after the temperature rises.
5, processing, such as found at the mouth of the feed material or puffed into a solidarity block to turn back, and the smell of burnt water vapor, that is because of too little material, the temperature rises sharply caused by such as blocking the serious, unable to feed, you can shut down the machine to remove, cleaned in the reboot.
6, after the end of processing, let the machine idle for 15-30 seconds, to be inside the residual material all processed before you can turn off the power, remove the head nut, screw, screw set, remove the residual debris to clean for the next time you use.

Fish food manufacturing machine

Many people will raise fish, cats, dogs, but for the feeding of pets, is also a headache,fish feed extruder can reduce the cost of feeding, reduce the labor intensity of feeders, feed puffer adopts advanced puffing technology, through high temperature and high pressure treatment of feed, so that it is puffed, sterilized and digested more easy for the animal's nutrient absorption, the process of work, the feed through the feeding system into the puffer, the feed is rapidly expanded, and finally, through the high temperature and high pressure treatment of feed, so that it is expanded, sterilization and digestion easier for animal nutrition absorption. During the working process, the feed enters the expander through the feeding system, the feed is expanded rapidly, and finally, through the cooling device, the feed is cured, cooled down, and the desired product is obtained. This is the working principle of this equipment.

Before proceeding with the installation of the puffer, you first need to select a suitable site. The size of the site area, ventilation, power connections, etc. are all considerations for site selection. In addition, it should be ensured that the site environment is clean and tidy, and there are no hazardous factors such as flammable and explosive substances.
Equipment transportation is an important part of the puffer installation, need to pay attention to the following points:
1. The equipment should be well protected against moisture and shock before transportation to ensure that the equipment will not be damaged when it arrives.
2. During transportation, attention should be paid to the center of gravity of the equipment to avoid accidents such as overturning.
3. The equipment should be checked in time after arrival to ensure that the equipment is intact.

After the installation is completed, the equipment needs to be debugged. The specific steps are as follows:
1. Check the normalcy of all electrical wiring, hydraulic piping and gas piping of the equipment.
2. Turn on the equipment and check whether the rotation direction and speed of the equipment are correct.
3. Adjust the process parameters of the equipment, according to the nature of raw materials and process requirements to reasonably adjust the parameters.
4. Carry out test run to check the puffing effect and the stability of the equipment.

Automatic fish feed making machine

High-temperature and high-pressure hydrothermal treatment process materials in the extrusion process, due to the heat generated by mechanical friction, or due to the direct steam sent into the puffing chamber, or into the puffing chamber jacket of the indirect steam heating temperature and pressure gradually rise. Materials in the high temperature and high pressure environment, water absorption and expansion, softening of the texture, under the action of mechanical force collapse, refinement, homogenization, cell wall rupture, molecular structure is broken up, starch paste, protein denaturation. Physical nature of the qualitative changes. Therefore, the spiral extruder also has a "continuous cooker" name.

Hot Tags: feed extruder machine, China feed extruder machine manufacturers, suppliers, factory, fish feed manufacturing machine, machine for making fish feed, mini fish feed machine, Fish Meal Extruder Machine, feeding machine for fish, Small Floating Fish Food Machine