Poultry Feed Pellet Making Machine

In recent years, the theme of environmental protection is getting hotter and hotter, and the pellet market is also getting better and better. Many people have invested in the pellet pelletizing industry. Many people in the operation of the pellet machine often encounter this or that problem. So today we will discuss the installation of the ring mold together.
Now on the market, the ring die installation methods mainly include: bolt coupling installation, taper coupling installation and hoop coupling installation.
Bolt coupling installation is simple, the ring mold is not easy to tilt, but the concentricity is not good and the ring mold bolt holes and empty shaft drive wheel bolt hole location degree does not match, after installation may be a single bolt force, the bolt is easy to break, the selection of the ring mold requires suppliers to ensure that the location of the screw holes degree, and the requirement to use the rotary mold drilling.
Taper coupling installed ring mold centering performance is good, transfer torque, ring mold fixing bolt is not easy to shear off, but the use of bolt loosening, drive wheel on the taper wear, we must notify the supplier of the ring mold on the taper of the size of the head diameter of the enlarged a little bit of the ring mold production can not be standardized.

Animal pellet making machine

First of all, after we receive the goods, first check all the parts and the pellet machine there is no lack or defects, if there is an instant replacement to find manufacturers, if not, then we need to test the machine before the gearbox to add hyperbolic gear oil to the oil level above. In the test machine, we need to add a small amount of water to the cornstarch, to achieve the state of the hand into a ball, loose that is scattered. Then we will mix the wet corn into the oil for 15 minutes, the first time we mix in about 1-1.5kg, the amount depends on the humidity of the corn meal.
Secondly, before the corn meal is poured into the flat die pellet machine, the machine should be empty to try to run first, but also pay attention to loosen the mold in time. If there is no problem, you can mix the cornstarch with oil and pour it into the pellet machine in small quantities, and the voltage should be kept at about 220v. Then to determine the success of the material can be discharged and do not block the machine, you can appropriately increase the amount of input, but need to pay attention to the material can not be dialed by hand, so as not to hurt themselves. Molded pellets should be poured into the pellet machine again, so that repeated grinding for 15 minutes.
Secondly, before the corn flour is poured into the flat die pellet machine, the machine should be empty and try to run first, and also pay attention to loosening and tightening the mold in time. If there is no problem, you can mix the cornstarch with oil and pour it into the pellet machine in small quantities, and the voltage should be kept at about 220v. Then to determine the success of the material can be discharged and do not block the machine, you can appropriately increase the amount of input, but need to pay attention to the material can not be dialed by hand, so as not to hurt themselves. Molded pellets should be poured into the pellet machine again, so that repeated grinding for 15 minutes.

livestock feed pellet machine

The grinding process of a feed pellet mill involves several critical steps to ensure the performance of the machine and the quality of the final product. Below are the specific grinding methods.
Preparation stage: first, ensure that you find a suitable container to place at the discharge of the pellet mill to facilitate the collection of raw materials generated during the grinding process for recycling.
Start-up operation: Next, start the pellet mill.
Add oil: Add the oil to the feed bin, taking care not to overfill the feed bin, so as not to affect the grinding effect.
Die plate grinding: Oil passes through the die hole to grind the die plate, which is the key step, through the flow of oil and pressure effect, the die plate is polished meticulously.
Cyclic grinding: Continuous cyclic grinding, the time is usually 40-60 minutes, to ensure the uniform grinding of the die plate.
For grinding before first use, especially for flat die feed pellet mills and ring die feed pellet mills, the following methods are recommended.
Flat die feed pellet mill: you can try the machine with mixed raw materials first, and then put in raw materials for normal production after the feed pellet mill repeatedly extrudes for 15-40 minutes.
Ring die feed pellet mill: the raw materials need to be increased and need to be repeatedly extruded by the ring die feed pellet mill for 30-50 minutes before inputting the raw materials for normal production.

Hot Tags: poultry feed pellet making machine, China poultry feed pellet making machine manufacturers, suppliers, factory, Mini Fish Food Making Machine